Vera Olkhovskaya
This belt processing technology is applicable only to individual tailoring.
Of course, "denim" is a conventional name.
In this article, we will look at the processing of the belt, suitable for skirts and trousers made of jeans with a trouser-type closure.
This waist treatment is also suitable for ladies trousers and shorts made of trouser-type silk, wool and other not too thick fabrics.
The content of the article:
- Do-it-yourself pattern of belt details for women's trousers, shorts or skirts.
- My ready-made patterns in which such processing of the belt is used.
- Patterns of women's trousers, shorts, skirts and overalls.
Please note: the figures show the ladies' version - the left PP is on top.
1. Do-it-yourself pattern of belt details for women's trousers, shorts or skirts
We start by cutting out the details of the belt: these are two rectangles with a length
St + 10 cm (where 10 cm is an allowance for processing the fastener from the middle seam)
and width
two widths of the finished belt + 2 cm.
The cut-out parts of the belt are duplicated from the inside (Fig. 1 a), while the dubbing is glued only to half of the part with an indent from the edge of 1 cm.
If you use a special non-woven adhesive tape for the belt, the indent is not needed.
Then oh
The tstup is folded inside out and ironed (Fig. 1b).
The belt blanks are folded along the midline and ironed again (Fig. 1 c, d).
Loops, if they are provided by the style, are made from a strip of fabric 3 cm wide.
First, the strip is overcast on one side (Fig. 2 a), then folded and stitched with one or two finishing lines (Fig. 2 b), and only after that it is ironed and cut into pieces of the desired length.
Finished belt loops are attached to the waist section in ladies' trousers arbitrarily (Fig. 3), if their function is decorative, and in certain places, if they must hold the product.
The best places for belt loops are: the top point of the ironing line of the PP, the middle point of the waist cut of the RFP.
It is better not to put a belt loop on the side cut - it fills the waist.
And the fifth loop on the cut of the seat will always come in handy, especially if your trousers are low-waisted.
So, before stitching the belt, you should have ready: pockets, side seams (carefully ironed out), clasp, seat cut (overcast), belt loops (sewn) and belt blanks.
If there are pockets, a notch is made on the burlap near the top bartack (Fig. 4).
The length of the notch is 1 cm, that is, it is equal to the width of the seam for attaching the belt.
After completing the notches, we proceed to stitching the belt.
Place the blank of the belt on the PP of the trousers with the face of the non-duplicated side to the face of the trousers, letting go 1 cm beyond the edge of the fastener (Fig. 5, 6) and stitch.
Burlap under this line is NOT enclosed.
Bend the duplicated side of the belt over the front of the trousers and stitch its end near the fastener, as close to its edge as possible.
Turn the turned end inside out and iron it.
Lay the finishing line along the perimeter of the belt, placing burlap under it, which did not fit under the first line.
Stitch the loose ends of the belt loops and sweep the seam of the seat, carefully matching the edges of the belt.
The sample is ready.
On the fitting, specify the volume of the belt.
After, process the seam of the seat and sew the last, fifth loop.
See also "Pants Handling", "Processing the skirt belt" и "Processing the waist cut without a belt"...
2. My finished patterns in which such processing of the belt is used
2.1 Pattern of trousers of carrots for sizes from 42 to 62
The differences between the old (bananas) and the new models (carrots) are that the “carrots” have only a small “filling” in the hip area, and the “banana” not only in the hip area, but also in the knee area.
Sewing difficulty level: easy, for beginners who have already sewn a skirt.
For tailoring, you can use thin dense knitwear and thin suit fabrics.
Consumption: 130 - 150 cm
The pattern is accompanied by a detailed description of the sewing of this model with illustrations.
Download a pattern of trousers and read instructions on how to sew ...
2.2 Pattern of women's boho trousers for sizes from 40 to 64
The level of difficulty in sewing boho trousers depends on the chosen processing option - from simple to medium. This pattern is for those who have already mastered sewing simple trousers at home.
The style is suitable only for slender girls with narrow hips.
The belt pattern is not included with the kit, as the belt is a strip of fabric. Further in the description, read how to cut it. The facing pattern is also not included in the set of patterns, but the cutting of the facing is given in the description and is carried out according to the same patterns of PP and RFP.
For sewing these trousers, it is better to use thin and very thin, stable fabrics. For example, thin dress jeans, dress cotton satin, shirt chintz, thin linen and poplin.
Read the instructions and download the boho trousers pattern...
2.3 Pattern of a long narrowed wrap skirt for sizes 40 to 52
A ready-made pattern of a long wrap skirt for beginners with instructions on how to sew such a skirt with your own hands. Sizes: 40-52. The sewing difficulty level is simple - a pattern for beginners who have mastered sewing a straight skirt.
For sewing the "top" skirt, you can use any "wool". For example, for the demi-season option, you can take both dress "wool" and semi-drape (lightweight drape), thin boucle or tweed. For spring and summer, silk fabrics are suitable. Heavy silk, raw silk, jacquard, thick linen and even denim.
In any case, it must be a stable fabric, stretch will not work, unless you use tight knit with very little stretch.
Download a pattern of a long wrap skirt and how to sew ...
3. Patterns of women's trousers and shorts, skirts, overalls
Join my community on Viber...
